Liners Under the Block Paving: An Honest Look at No-Dig Drain Repair
Photo: trenchless drain repair cured in place pipe liner installation excavation, via i.pinimg.com
A cracked pipe under a newly laid drive is one of those problems that arrives with a horrible sense of timing. The drainage is forty years old, the block paving is four months old, and the first anyone knows about the fracture is a patch of damp at the edge of the patio.
Then the quotes come in. One contractor wants to lift twelve metres of block paving, excavate, replace and reinstate. Another says they can line it, no mess, done in a day. Both are telling you part of the truth. The trick is working out which part applies to your pipe.
What trenchless repair actually involves
It isn't magic, and it isn't invisible. A lining job starts with two small excavations — an access pit at each end of the damaged stretch — plus a proper CCTV survey and a thorough clean using high-pressure jetting and often a chain flail to scrape off scale and roots.
Then there are two broad options:
- Patch liner. A short resin-soaked sleeve on a packer, positioned over a single crack or open joint and inflated against the pipe wall until the resin cures.
- Full-length liner (CIPP). A felt or glass-fibre tube impregnated with resin, pulled or inverted into the run, inflated, then cured with hot water, steam or UV light. Afterwards a robotic cutter reopens the branch connections.
That's the process. The important bit is what it can and cannot achieve.
What a liner genuinely fixes
Cracks, hairline fractures, slightly open joints, internal corrosion and pitting, minor holes, and root intrusion — once the roots have been cut back. It also seals the pipe against groundwater infiltration, which matters in those wet Cheshire winters.
Critically, a liner holds its shape only because the host pipe still has shape. It is a structural repair relying on the original pipe as a mould.
Where it stops working
This is the bit the sales patter skips.
- Loss of shape. If the pipe has deformed beyond a modest amount, the liner simply copies the deformity and you've spent money preserving a problem.
- Collapse or partial collapse. A liner needs something to line.
- Significant displacement. Where a joint has shifted enough to restrict the bore, a thin sleeve won't restore capacity.
- Backfall or a belly. A liner follows the sag. It doesn't put fall back into a run that never had it or has settled over decades.
- Voids behind the pipe. If soil has washed away and the pipe is effectively hanging in a hole, a liner gives you a very neat tube floating in nothing. Ground movement will finish the job.
- Heavy encrustation. Old iron with thick scale sometimes can't be cleaned well enough to bond properly, and the bore may already be too tight to line without choking flow.
The lifespan conversation
Manufacturers will tell you fifty years. That's a laboratory figure under ideal conditions. In the real world, lifespan comes down to preparation, resin quality, cure method, liner thickness, and — crucially — whether the ground around the pipe keeps moving.
Parts of the North West sit on shrinkable clay, and there are old workings under more postcodes than people realise. A well-installed liner in a stable pipe will comfortably see out decades. A hastily installed one in a pipe that's still shifting is a different proposition entirely.
Read the guarantee properly
Ask these before anyone starts:
- Is it a workmanship guarantee or a product warranty? They are not the same thing.
- Is it insurance-backed, and with which provider?
- Does it cover the whole run or just the section that was lined?
- What's excluded? Root re-entry at unlined joints either side, ground movement and third-party damage usually are.
- If the firm stops trading, who honours it?
- Will you get pre- and post-lining CCTV footage, dated and labelled?
If the answer to the footage question is vague, walk away. A contractor who won't show you before and after has something to hide.
Questions to put to the contractor
- Can I see the pre-lining survey with the defects marked and explained?
- What liner thickness and material are you using, and what does that achieve structurally?
- Are you cutting roots back and sealing the joint, or just covering over it?
- How are branch connections reopened and made watertight?
- What happens at each end where the liner meets the old pipe?
- What would excavation cost, and why is lining the better answer here?
- Is this actually the water company's pipe? If the run is a public sewer, lining it may not be your bill at all.
- Are there tree preservation orders or conservation area rules that affect the access pits?
- What reinstatement of the drive is included, and to what standard?
When digging is honestly the better call
A collapsed section. A single shallow defect with easy access, where excavation can be cheaper than mobilising lining kit. Multiple defects along a run that also sags. A drive that's being replaced next spring anyway. Or a pipe already tight on bore, where a liner would rob you of capacity you can't afford to lose.
No-dig is a good tool, not a universal answer. Any contractor who tells you otherwise is selling rather than advising — and a lining job still means two holes in your drive, so agree where those pits go and what the reinstatement looks like in writing before the van arrives.